COMPOSITE FABRICATOR

Summary This is a public notice flyer to notify interested applicants of anticipated vacancies through the Domestic DIB, MRTFB Direct Hire Authority. Applications will not be accepted through this flyer. Interested applicants must follow the directions in the "How to Apply" section of this flyer to be considered. There may or may not be actual vacancies filled from this flyer. Notice of Result letters will not be sent to applicants who respond to this flyer. Responsibilities You will fabricate and lay up composite material to form composite skin panels or repair parts to dimensions and stacking order specified by technical directives. You will determine tooling requirements for fabrication of new assemblies as well as repair of composite assemblies. You will analyze damage to critical flight components and determine the type of repair configuration to be utilized. You will perform planning, layout, modification, fabrication and research of unconventional developmental advanced composite assemblies working in close coordination with engineering but with a minimal supervision. Requirements Conditions of Employment Qualifications Although a specific length of time and experience is not required for most trade and labor occupations, you must show through experience and training that you possess the quality level of knowledge and skill necessary to perform the duties of the position at the level for which you are applying. Qualification requirements emphasis is on quality of experience, not necessarily the length of time. Your qualifications will be evaluated on the basis of your level of knowledge, skills, abilities and/or competencies in the screen out listed below. This job has a screen-out element which will be used to determine minimum eligibility for this job. Applicants who do not receive a minimum of two points on the screen-out element(s) will be found ineligible. The Screen-out Element for this position is: ABILITY TO DO THE WORK OF an COMPOSITE FABRICATOR, WG-4352-10 without more than normal supervision such as: Developing and fabricating individual ply flat patterns to accurately position and orient each lamina within the laminate; Using flat patterns to cut individual plies from a variety of unidirectional advanced composite prepregnated; Fabricating and laying up composite material to form composite skin panels or repairs parts to dimensions and stacking order specified by technical directives; Adhering to and within acceptable standards using technical manuals, publications, TEIs, LESs, AFCs, LPSs, blue prints and 3R instructions; AND Utilizing cold working training practices i.e., using measuring equipment, micrometers, ball gauges, scales, no-go gauges and installation procedures for interference fit fasteners with (+.001) tolerance. Additional qualification information can be found from the following Office of Personnel Management website: https://www.opm.gov/policy-data-oversight/classification-qualifications/federal-wage-system-qualifications/#url=WG-4300 Experience refers to paid and unpaid experience, including volunteer work done through National Service programs (e.g., professional, philanthropic, religious, spiritual, community, student, social). Volunteer work helps build critical competencies, knowledge, and skills and can provide valuable training and experience that translates directly to paid employment. Education Additional Information This position is covered by the Department of Defense Priority Placement Program. Several vacancies may be filled. A tentative offer of employment will be rescinded if the selectee fails to meet the pre-employment requirements, including failure to report to any of the scheduled appointments. Federal annuitant information: The selection of an annuitant is subject to the Department of Defense and Department of the Navy policy on the employment of annuitants. Policy information may be found at: http://www.secnav.navy.mil/donhr/Documents/CivilianJobs/FedCivAnnuitants.pdf. Veteran's preference does not apply when selecting individuals under this specific hiring authority. However, if you claim veteran's preference, you will be required to submit supporting documentation with your application as described in the Required Documents section below. Military Spouse Preference applicants will receive priority consideration at the Full Performance Level (FPL) and if determined to be Best Qualified at the FPL, and selected, must be placed at the FPL. A BQ military spouse possesses knowledge, skills, abilities, and competencies comparable to others who meet the competitive referral criteria for the specific position. PPP applicants will be placed at the FPL, if determined Well Qualified (WQ). To receive priority consideration, the FPL must be the same grade level or equivalent of the retained grade or the grade held immediately prior to separation. Preference applicants will be placed at the highest grade for which they have applied and are determined Best Qualified (BQ). A BQ military spouse possesses knowledge, skills, abilities, and competencies comparable to others who meet the competitive referral criteria for the specific position.